Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
The content listed below relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really attention-grabbing. Don't skip it.
Installing a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also place the new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is better to consider employing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a brand-new tub in your washroom if you have already acquired a brand-new tub and do not require to change the setup of your previous water system pipes.
Your tools and also product checklist ought to make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be fairly troublesome due to the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water and also examine all joints and new pipework for leaks as well as tighten them if needed. Fill up the bathtub and also check the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait till the bath tub has been used at least once as this will settle it into its last placement.
Planning for the Installment
To start with, the sustaining framework provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bath as well as the tiling, leading to issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that article about Tools You Need to Install a New Bathtub from an acquaintance on our other website. Are you aware of somebody else who is fascinated about the niche? Take a moment to share it. Thanks for your time. Come back soon.
Book Today
Report this page